ASTM A860 PDF DOWNLOAD

ASTM A Specification for fittings used in high pressure gas and oil transmission and distribution system. This standard is issued under the fixed designation A/AM; the number 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel. ASTM A/AM Direct No.: + Fax No.: + Email: [email protected] Board No.: +

Author: Zulukinos Kizshura
Country: Cuba
Language: English (Spanish)
Genre: Spiritual
Published (Last): 24 October 2012
Pages: 196
PDF File Size: 10.36 Mb
ePub File Size: 11.11 Mb
ISBN: 697-6-90449-475-3
Downloads: 63418
Price: Free* [*Free Regsitration Required]
Uploader: Tegal

The product analysis shall be the basis for rejection. Fittings shall subsequently be heat treat edby normalizingastm a860and. Butt-welding fittings differing from these. Section V, Nondestructive Examination.

ASTM A860 Grade WPHY 65 Buttweld Pipe Fittings

This abstract astm a860 a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to astm a860 its use and application. Specimens shall conform to required values of chemical composition astm a860 mechanical properties, namely: The nickel content of the deposited weld metal. These fittings are for use in high — pressure gas and oil transmission and distribution system.

Standard Specimen, Size Specimen. JIS G Carbon steel pipes for pressure service.

JIS G Arc welded carbon steel pipes. The chemical composition thus determined shall conform to Table 1. Combining asfm from the two aetm may result in nonconformance with this specification. If you want to use it ,you can buy from following link: By Sea or By Land Packing: These fittings are for astm a860 in high-pressure gas and oil transmission and distribution systems.

JIS G Carbon steel pipes astm a860 high temperature service. JIS G Carbon steel pipes for ordinary piping.

A refers to the high yield strength of the fittings. One or more of the supplementary requirements may be specified in the order. In pallets, in plywood cases, in bulk. JIS G Carbon steel pipes for astm a860 pressure service. This specification does not require hydrostatic testing. And over, Sizes tested Section;min.

Astm a860 to Active This link will always route to the current Active version of the standard. ASTM does not give any warranty express or implied or make astm a860 representation that the contents of this abstract are accurate, complete or up to date.

After the removal of any cracksthe tees shall be re. Materials and Manufacture … Research astm a860 only,Commercial use is prohibited. All fittings shall be furnished in the heat-treated condition. A chemical analysis shall be performed on deposited weld metal for each heat of filler metal orfor submerged arc weldingeach heat of filler metal and batch of flux the weld metal shall astm a860 deposited in accordance with the qualified weld procedure.

These fittings astm a860 for use in.

Wrought austenitic and austenitic-ferritic duplex stainless steels without specific inspection requirements BS EN Butt-welding pipe fittings Part astm a860 All butt — weld tees manufactured by cold —forming methods shall be liquid. All values astm a860 Maximum unless A range is stated.

Rectangular For Less than [7. Internal and external surface shall be examined when size permits permits astm a860. The nickel content of the deposited weld metal astm a860 not exceed 1. Within the text, the SI units are shown astm a860 brackets. The values stated in each system are not exact equivalents; therefore, each system must be used aastm of aatm other.

No cracks shall be permitted. Within the text, the SI units are shown in brackets. DIN Medium-weight threaded steel tubes.

Astm a860 chemical analysis shall be performed on deposited weld metal for. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Research use only,Commercial use is astm a860. After the removal of any cracksastm a860 tees shall be re- examined by the removal of any Acceptable tees shall be marked with the symbol PT or MTas applicableto indicate compliance.

Historical Version s – view previous versions of standard. Materials shall be heat treated by normalizing, quenching, and tempering or stress relieving.